NFB-1AMP Headphones Amp / Pre

NFB-1AMP Headphones Amp / Pre

€495.08

The full balanced design based on Master 9
Class A PSUs built in
Discrete  Headphone amplifier / Preamplifier
Super Exponential Volume Characteristic
8000mW at 40 ohm output
OCC and hi-end parts applied 

Quantity
In stock

  • WARRANTY
2 years warranty
Dedicated support WARRANTY 2 years warranty Dedicated support
  • SHIPPING
Worldwide delivery
DHL - FedEx SHIPPING Worldwide delivery DHL - FedEx
  • EASY RETURN
14 days satisfied or refunded EASY RETURN 14 days satisfied or refunded

Since 4th. April 2018,   the model had upgrade the volume ports:
The upgraded volume ports had built with Vishay or KOA resistors with dual resistors parallel ,  tolerance low to 0.05% .
volume4s.JPG



Different to the C-2 ( 11th Anniversary Edition ):

          The C-2 is a single ended head amp and preamp (+/- 30V DC high voltage power supply ),.
         The NFB-1AMP is balance head amp and preamp (+/-15V DC power supply ). So They had same output power specs and can drive most headphone very well.
  
         If customer like to keep your headphone with single ended connector (6.3MM), choice would be C-2 you get better performance than the NFB-1AMP.

         If customer have balanced connector headphone or can modify the headphone with balance connector, choice would the NFB-1AMP.


Summarize
Fully balanced class A design built by discrete analog stages without any OPA or coupling caps in the signal channels.

Non- feedback ACSS analog output stage.

8000mW at 40 ohm output, 16DB gain can drive the low sensitivity headphone very well.

Class A PSU's for DC supply. 

Uses most Hi-end grade parts and exactly matched transistors, OCC wires.

Four-channel 100 steps digitally controlled relay-based volume control avoids channel imbalance and improves sound quality .

Supper Exponential Volume Characteristic, easy match the volume with very high headphone / speaker without change the gain mode.

5 groups input: RCA X2, XLR X2, ACSS X1

Preamp output : XLR / RCA / ACSS

Headphone amp output: 4pins XLR X1 / 6.3MM X1
  

 

Technology detail 

Detail of the Current Conveyor (ACSS) Technology

Impedance matching:
              There are a lot different quality DACs. They have different design and output impedance . To avoid negative effect on sound quality by differences in DAC's output impedance, in the NFB-1 we have design a pair single-ended class A FET buffers in the input . All the RCA input signals go through these FET buffers, the output impedance become very low, even if the source have high or low output impedance. 

              The FET buffers working in pure class A , and it has a short signal journey. this way we can keep the sound quality without colouration ,(dry and harsh) .
              C-2inputs.JPG

Core:

             NFB-1AMP have the same ACSS design with our top grade model Master 9 . It is a pure class A design built by discrete analog stages without any OPA or coupling caps in the signal channels.
They seem complex , but in fact they are the most simple design the world has ever had .The simplest and shortest signal journey brings out the most neutral and least coloured sound.

            The ACSS is a non-feedback technology made with discrete amplifiers. Most people know the global feedback design can offer better specs in test measurements, and non-feedback can't do well in test measurements but can offer better sound for the human ears. Here is a conflict of the classic circuits. 

            But the ACSS opens a new field, it can offer a least colouration to the sound which is more neutral with very low distortion and high linearity. So it can retain the dynamics, detail and neutral sound (not bright or harsh.)

            All signal gain is in current mode all transistors work in class A mode.
The NFB-1AMP has all components exactly matched before installation.

                        Super low THD                                                 Flat frequency response
                     
NFB1AMPTHDs.JPG                                              M8Frs.JPG

Strong class A output stages:
             The NFB-1AMP has in its design a pare of diamond differential output stages, every parts have been exactly matched before assembly . 

             The output stages had four pair 15W transistors ,they also work in class A . (Drive most headphones)

              C2output.jpg

Power supply:     

           The class A parallel connection PSU has very high input impedance to avoid pulse through the PSU from affecting the preamp and low output impedance with very fast speed and high linear, so it is a very clean power supply.

           The NFB-1AMP applies separate linear PSUs for the display and control parts, to avoid noise going through power line and affecting the amplifier.

            C2PSUs.GIF

Volume control:
          The volume control is also different from conventional technology. Conventional volume control technology is the volume control implemented in the analog amp input stage through a volume pot to reduce the signal . The volume pot will affect quality of the sound directly , The low quality volume pot can cause loss of the detail and cause channel imbalances . Even the high performance volume pot still cause the detail loss. Whatever quality volume pots, will still cause the S/N being adversely affected .

           But in the NFB-1AMP , we applied the I/V conversion volume control , the volume control just a variable passive I/V conversion place at the ACSS amp output , where the output is the current signal, not the voltage signal. The volume control is I/V conversion, and the volume depends on the current (I) conversion to the voltage (V). (Like R-2R D/A chips output passive I/V conversion) It can keep the signal frequency band flat and not loose any detail. It want degrade sound quality at any volume level . After the volume , there are four groups diamond non-feedback buffer output stages with very low output impedance .

           Mark Levinson also knows that current volume control has great benefits, so in their Top End preamp NO.32 volume control, they use many components to change the signal to current signal (I), then implement the volume control , and then change back to voltage signal (V) again. 
 
          But NFB-1AMP is simply a more complete work in terms of the current signal, and technically, it is superior to conventional technology. The less conversion bring much neutral sound .

          In NFB-1AMP is applied a digital control relays based volume control. .NFB-1AMP has total four channels through changing the DALE resistors to control the volume avoid channels imbalances and achieve the best performance and sound quality.
NFB-1AMP have 100 steps volume control, which offers very smooth control for both high / low sensitivity headphone and speakers. While users change the volume, the combine relays break or close, it may had slightly switch sound on output and disappear when you stop changeing the volume.

              
NFB-1AMP Supper two sets Exponential volume characteristic  
                           NFBvolumes.JPG                         

Static storage mode control software:
          In most control software design, the MCU will continuously output data , the MCU has very high speed, so the output data become high frequency impulses and disturbs the audio signal circuits this adversely affects sound quality . In our product we have applied a static storage mode control software , the MCU output control data is saved into memory and its only used when you operate volume ,then it stop outputting data until users next operation. This design vastly improve sound quality ( clarity and transparency .)

Shield:

         The NFB-1 design has no compromises , it's built fully with aluminium , the transformer interference can't travel through the aluminium chassis and be transferred to the analog amps, and there are two shielded boards to insulate the transformer and the power supplies.
           
NFB1AMP8s.JPG

Components:
      
Uses all Hi-end grade components, including DALE resistors, WIMA caps, custom order NOVER (UK brand) caps.

S/N Ratio
 
>125DB (Volume minimum) 

THD
 
<0.002 %   NFB1AMPTHDs.JPG


Gain
 

Gain : +16DB


Volume characteristic
 

Two sets Exponential Volume Characteristic

 NFBvolumes.JPG
Headphone amp Output Power 9900MW /  25 ohm 
8000MW /  40 ohm 
 3500MW  /  100 ohm
1200MW / 300 ohm
600MW  /  600 ohm

 

 Preamp Output Level (Max)

10V @ RCA
20V @XLR
2.4MA @ ACSS

Output impedance

1 ohm 


Input impedance
 

47K ohm @ RCA
94K ohm @ XLR
<10 ohm @ ACSS

Frequency Breadth (XLR input)

20Hz - 20KHz ( +/- 0DB )
1Hz - 220K (+0DB, -3DB)

M8Frs.JPG

Channels cross
 
> 120DB

Channels imbalance
 
< 0.05DB

Power Requirement

1 Version  100-120V  AC 50/60 Hz
2 Version  220-240V  AC 50/60 Hz

Power Consumption

30W @240V or 120V

Package Weight

Approximately 5KG


Dimensions
 
W240 X L360 X H80 (MM, Fully aluminium )  

Accessories

Power cord  X1

100 Items

Specific References

You might also like

16 other products in the same category:

Reviews

No customer reviews for the moment.

Write your review

NFB-1AMP Headphones Amp / Pre

The full balanced design based on Master 9
Class A PSUs built in
Discrete  Headphone amplifier / Preamplifier
Super Exponential Volume Characteristic
8000mW at 40 ohm output
OCC and hi-end parts applied 

Write your review